You are here: Home » News

News and Events

formwork

Knowing that you are interested in formwork, we have listed articles on similar topics on the website for your convenience. As a professional manufacturer, we hope that this news can help you. If you are interested in learning more about the product, please feel free to contact us.
  • Can Kwikstage Components From Different Suppliers Be Mixed?

    2026-11-12

    Kwikstage scaffold compatibility cannot be established by product name or tube diameter alone. Components from different suppliers may appear to engage, yet differ in V-lock geometry, wedge taper, end-fitting dimensions, tolerances, materials or load data. Mixing them without a documented check can alter the connection and the structural integrity of the erected scaffold. The practical answer for a rental fleet or contractor is to identify the existing system, compare drawings and physical samples, obtain load information for the intended combination and have a competent designer approve the arrangement before use. Buying a complete matched bay from one supplier is simpler, but top-up orders are common and can be assessed properly. This guide gives seven checks, a supplier RFQ list and a clear distinction between a physical trial fit and a verified working scaffold. Read More
  • Kwikstage Transom Sizes: Matching Platforms To Bay Widths

    2026-11-10

    Kwikstage transom sizes should be selected from the required platform width, the actual plank dimensions and the system's approved bay layout. A transom runs across the scaffold between standards and helps support the working platform; a ledger runs along the bay. A nominal transom length does not, by itself, reveal the clear usable deck width or how many boards will fit. End fittings, standard positions, board overhang, gaps and special access pieces all affect the result. Buyers should therefore ask for a drawing showing transoms, planks and guardrail or hop-up arrangements together. This guide walks through five checks for a platform schedule and explains why a “three-board transom” label must be tied to the selected plank and system. The engineered scaffold design still controls loading, bracing, ties and erection. Read More
  • What Affects Aluminium Formwork Reuse And Project Cost?

    2026-11-09

    Aluminium formwork reuse lowers cost per pour only when enough panels can move through enough suitable pours without excessive modification, damage or idle time. The number printed in a supplier brochure is not the number your project will achieve. Count the repeated floor plans, identify one-off areas, estimate labour and repair, and give residual value a conservative basis. Then divide the net system cost across the actual usable pours, not a theoretical service life. This is especially important for contractors comparing an upfront panel purchase with rental, steel forms or plywood on a mixed building. A buyer should ask for a panel schedule, not only a price per square metre, because corner pieces, fillers, ties, props and handling all affect the economics. This guide provides a six-factor model and a simple calculation method without promising a universal reuse count. Read More
  • Aluminium Formwork Layout Planning: Panels, Openings And Corners

    2026-11-06

    An aluminium formwork layout starts with the building drawings, wall thicknesses and pour sequence, then assigns panels around the fixed geometry. Put inner and outer corners, door and window openings, slab edges, ties and service penetrations on the plan before filling straight wall runs with standard panels. This order exposes awkward residual widths early and keeps small filler panels from multiplying across repeated floors. A layout is more than a panel count: it tells the erection crew which parts meet, where concrete pressure is restrained and how the form can be stripped. For a B2B buyer, the approved layout drawing is also the basis for a reliable bill of materials and quotation. This guide explains seven checks to make before ordering, using millimetres and drawing references rather than unverified universal panel dimensions. Read More
  • Steel Prop Top Plates And U-Head Jacks: What Is The Difference?

    2026-10-29

    A steel prop top plate provides a flat bearing surface; a U-head jack has a fork-shaped head intended to locate a compatible beam or other specified member. The distinction matters because the head is the first interface in the temporary support load path. A beam that sits on a plate is not automatically restrained in the same way as one seated in a correctly sized U-head. Conversely, a U-head does not fix an inadequate beam, prop or foundation. The project designer must check the load, bearing width, connection detail and prop model at its actual extension. This guide compares the two head options and lists five questions to send with a formwork enquiry. It avoids assigning a universal capacity to either head because the permissible load depends on the exact components and the complete engineered arrangement. Read More
  • How Steel Prop Extension Length Affects Rated Capacity

    2026-10-27

    Steel prop extension length affects the capacity available from a specific adjustable prop, so buyers should check a load chart at the actual installed height. A telescopic prop has an inner tube, outer tube, adjustment pin and threaded screw or collar. As the inner tube is extended, the geometry of the supported member changes. The permitted load also depends on the product design, end restraint, bracing and whether the load is applied concentrically. There is no defensible universal “tons per prop” value across every extension. Tianjin Easy Scaffolding’s internal card lists a broad height range of about 1.7–3.0 m and historical capacity notes, but those are not a project load table. This article explains five checks that belong between the formwork drawing and the purchase order, with emphasis on the extension shown for each prop location. Read More
  • How To Select Steel Prop Height Ranges for Slab Formwork

    2026-10-26

    An adjustable steel prop height range should cover the installed support height after accounting for the formwork panel, beams, head and base. Floor-to-floor height alone is not the prop length. The prop also has to carry the calculated reaction at that particular extension and be used within its manufacturer’s adjustment instructions. Tianjin Easy Scaffolding’s internal steel-prop card gives an approximate 1.7–3.0 m range for some products, but it does not identify a universal model or capacity at every setting. The right selection begins with a section drawing, then checks minimum and maximum extension, screw travel, load chart, bracing and bearing. This guide gives a five-step selection method for buyers preparing a slab formwork RFQ. It keeps physical fit, rated load and construction sequence as separate checks so one convenient height number does not hide a support problem. Read More
  • Galvanised Vs Painted Steel Scaffold Planks: Buying Considerations

    2026-10-16

    A galvanised scaffold plank uses a zinc coating to protect its steel surface; a painted plank relies on a different barrier coating. Neither finish replaces checks on board design, hook fit, load data or condition. For outdoor purchasing, compare the exact coating process, coverage at cut edges and welds, handling damage, maintenance plan and total project use. “Galvanised” is too broad to specify an order by itself: a plank made from pre-galvanised sheet is not the same purchasing description as a completed plank hot dip galvanised after fabrication. Tianjin Easy Scaffolding’s internal range notes list hot dip galvanised, pre-galvanised and painted steel planks, but buyers should confirm which finish is offered for the selected SKU. This article gives a five-point finish review that distributors and contractors can use alongside the platform’s structural and dimensional requirements. Read More
  • How Ringlock Rosette Connections Work And What To Inspect

    2026-10-13

    A ringlock rosette connection joins a ledger or diagonal brace to a vertical standard at a welded node. The fitting at the member’s end seats on the rosette, and a wedge pin secures the connection. That simple sequence is useful for quick erection, but a fitted-looking joint is not enough to establish that parts are compatible or fit for reuse. Check the rosette, weld, ledger head and wedge before assembly, then inspect the complete scaffold according to the project plan. A connection also has to work with the intended bay geometry, brace arrangement and loading. This guide explains the parts, the assembly principle and seven practical inspection points for buyers and site teams. It does not assign a safe working load to an individual joint; that value must come from the manufacturer’s data for the specified system and configuration. Read More
  • Total 3 pages  Go to Page
  • Go

ABOUT US

Tianjin Easy Scaffolding Co., Ltd

With 17+  years experience in scaffolding industry. Our market mainly covers North America, South America, Australian, New Zealand; South East Asia and Middle East.
 

QUICK LINKS

CONTACT US

Contact Us
Copyright © 2022 Tianjin Easy Scaffolding Co., Ltd. | Sitemap | Privacy Policy